[Rhodes22-list] FW :CB Cleat

[TN Rhodey]

Rory - Good advice. The only thing I would add is I would overdrill old 
holes a tad then fill with marinetex or thickend epoxy. Then redrill.

Wally


>From: Rory Orkin <roryorkin at earthlink.net>
>Reply-To: The Rhodes 22 mail list <rhodes22-list at rhodes22.org>
>To: rhodes22-list at rhodes22.org
>Subject: Re: [Rhodes22-list] FW :CB Cleat
>Date: Thu, 17 Aug 2006 18:58:24 -0700 (PDT)
>
>
>I am guessing that only screws hold in the cleat --Perhaps you have tried
>this already.. Remove cleat- fill holes in fiberglass with marinetex.. Let
>cure completely-- redrill holes with appropriate (smaller) holes for the
>screws -- then put screws back in
>you could also bed the cleat with an appropriate bedding compound to assure
>no water penetration.
>I would think that would work
>                                                Rory
>
>
>Tootle wrote:
> >
> > Slim:
> >
> > Slim:
> >
> > My fuse box is in the new location.  I have a small cover over the old
> > place.  I suspect that the answer to your question is you could get one
> > hand in there.  However, I suspect as huge as you are that if scooted up
> > in the space between the cooler and the centerboard that you would have
> > better access to see what you are doing.  You might want put your hand 
>in
> > there while watching from underneath.  In that case you would need to 
>take
> > your shoes and socks off and use your toes to hold the bolt.
> >
> > Ed K
> > Greenville, SC, USA
> > Addendum:  Law of the Workshop:  Any tool, when dropped, will roll to 
>the
> > least accessible corner.
> >
> >
> >
> >
> > Slim-2 wrote:
> >>
> >> I haven't done enough exploration but can you access that place through
> >> the
> >> electrical panel beneath the companionway?
> >>
> >> Slim
> >>
> >> On 8/16/06 5:14 PM, "Bob Weber" <ruba1811 at hotmail.com> wrote:
> >>
> >>> Slim, you could shape wood to fit in the groove underneath and screw
> >>> into
> >>> that or you could use a nut and a bolt with a backing plate.  Bob W
> >>>
> >>>
> >>>> From: Slim <salm at mn.rr.com>
> >>>> Reply-To: The Rhodes 22 mail list <rhodes22-list at rhodes22.org>
> >>>> To: Rhodes22-list <rhodes22-list at rhodes22.org>
> >>>> Subject: Re: [Rhodes22-list] FW :CB Cleat
> >>>> Date: Wed, 16 Aug 2006 17:04:37 -0500
> >>>>
> >>>> I was trying to send the picture from my phone--haven't worked out
> >>>> those
> >>>> bugs yet.  But see the pic in the previous post.  The screws that
> >>>> secure
> >>>> the
> >>>> CB cleat keep stripping out because there's not much of anything for
> >>>> them
> >>>> to
> >>>> bite on.  Any suggestions?
> >>>>
> >>>> Slim
> >>>>
> >>>> On 8/16/06 5:01 PM, "salm at mn.rr.com" <salm at mn.rr.com> wrote:
> >>>>
> >>>>> You have new Picture Mail!
> >>>>>
> >>>>> Click Go/View to see now.
> >>>>> 
>http://pictures.sprintpcs.com/?mivt=REor4xYB25hFk7AUaLIL&shareName=MMS
> >>>>>
> >>>>> _frsthgl
> >>>>>
> >>>>> __________________________________________________
> >>>>> Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list
> >>>>
> >>>> __________________________________________________
> >>>> Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list
> >>>
> >>>
> >>> __________________________________________________
> >>> Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list
> >>
> >> __________________________________________________
> >> Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list
> >>
> >>
> >
> >
>
>--
>View this message in context: 
>http://www.nabble.com/FW-%3ACB-Cleat-tf2118133.html#a5860776
>Sent from the Rhodes22 forum at Nabble.com.
>
>__________________________________________________
>Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list