[Rhodes22-list] Now note to Elle

Wed Apr 15 11:20:10 EDT 2009

Elle,
congratulations on your commissioning for photos, hope you can share a few with us.  We've always enjoyed your photos.

Rehabbing an old house?  Where did that come from?  This is not your house??  Got Watermusic out much yet? - rob

-----Original Message-----
From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of elle
Sent: Monday, April 13, 2009 4:32 PM
To: The Rhodes 22 Email List
Subject: Re: [Rhodes22-list] By way of introduction, Ahoy,and request for advice

HI, Rob,
Nope....still here! 
I've been busy with photog stuff..workshops in MD, and finishing shooting projects that I'm committed to. I've ben commissioned to shoot a series of four locations in this area, so I've been working on that, also.
Also....my BF & I are staying busy...;^)....( rehabbing a turn of the century Four Square home ).......thought I was going somewhere else with that, didn't ya!
elle

We can't change the angle of the wind....but we can adjust our sails.

1992 Rhodes 22   Recyc '06  "WaterMusic"   (Lady in Red)

--- On Mon, 4/13/09, Lowe, Rob <rlowe at vt.edu> wrote:

From: Lowe, Rob <rlowe at vt.edu>
Subject: Re: [Rhodes22-list] By way of introduction, Ahoy, and request for advice
To: "The Rhodes 22 Email List" <rhodes22-list at rhodes22.org>
Date: Monday, April 13, 2009, 9:01 AM

Elle,
Where you been?  Thought we'd lost you to "the dark side". - rob

-----Original Message-----
From: rhodes22-list-bounces at rhodes22.org [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of elle
Sent: Saturday, April 11, 2009 12:33 PM
To: The Rhodes 22 Email List
Subject: Re: [Rhodes22-list] By way of introduction, Ahoy,and request for advice

Hi, Andy,

A bit late on the greeting but welcome to the family & 'da list.'

I'm just up the road a piece & over a bridge or two from you....on the upper Northern Neck...we used to have a Rhodie or two in the Mobjack Bay & Newport News areas...not sure if they are still on the list.

elle

We can't change the angle of the wind....but we can adjust our sails.

1992 Rhodes 22 Recyc '06 "WaterMusic" (Lady in Red)

--- On Mon, 4/6/09, atmcneil <atmcneil at gmail.com> wrote:

From: atmcneil <atmcneil at gmail.com>
Subject: [Rhodes22-list] By way of introduction, Ahoy, and request for advice
To: rhodes22-list at rhodes22.org
Date: Monday, April 6, 2009, 11:28 AM

Hello everyone. I'm a new Rhodie, having gotten a used 1981 from Stan at the
beginning of March. I had her parked in the driveway for a few weeks while I
attended to paperwork and cosmetic concerns. I had folks on hand Saturday to
launch her. That was a challenging time, including losing control of the
mast and pulling the step out of the deck. Luckily I was able to quickly
repair it, having read Stan's reasons not to bolt the step to the deck. So
by 1pm I had her parked in her slip and had renamed her CEALA (pronounced
sea-la).

I went to check on her Sunday morning. She's in a slip on Queens Creek, off
the York River about 5 miles NW of Yorktown. I found she had taken on water
overnight, somewhere around 20-25 gallons.

Yesterday evening a friend and I went down and took some of the deck up to
try to find the leak while she was still in the water.  There are 3 bolts
coming up at the center board cap, and from the diagram in the "Centerboard
and Trunk Restoration" instruction on the website, the leak is where they
double block for the mechanical advantage is.  The fiberglass gasket is
leaking (about 1g/hr). The washers look too small and the edges of the
gasket have come up.  The cp trunk flange (the part with 40+ bolts) looks
good. While I working I dried them off and they stayed dry.

So we pulled her out and she is parked at the marina until Wednesday, at
which point I either have to put her back in the water or bring her to the
house.

I have a few questions. What will happen to the double mini blocks when I
remove the 3 nuts holding them? Will I be able to reached them to attached
them to a new gasket and plate?  What should I use as the plate to attach
the double mini blocks? One guy who looked said the plate should be
stainless with a rubber gasket under it. Another guy suggested using a blank
head gasket and then drilling the necessary holes.  I just want to make sure
I won't lose any of the mechanism for raising and lowering the centerboard.

Thanks for taking the time to read this. I hope I didn't ramble. I can
probably post a picture this evening if that would help. I look forward to
getting to know folks on this forum.

Andy

1981 R22 - CEALA
Williamsburg, Virginia

-- 
View this message in context: http://www.nabble.com/By-way-of-introduction%2C-Ahoy%2C-and-request-for-advice-tp22909129p22909129.html
Sent from the Rhodes 22 mailing list archive at Nabble.com.

__________________________________________________
To subscribe/unsubscribe or for help with using the mailing list go to http://www.rhodes22.org/list
__________________________________________________

__________________________________________________
To subscribe/unsubscribe or for help with using the mailing list go to http://www.rhodes22.org/list
__________________________________________________

__________________________________________________
To subscribe/unsubscribe or for help with using the mailing list go to http://www.rhodes22.org/list
__________________________________________________

__________________________________________________
To subscribe/unsubscribe or for help with using the mailing list go to http://www.rhodes22.org/list
__________________________________________________