[Rhodes22-list] Annapolis Show Attendees

[Michael Weisner]

Art,

Yes, we are planning to attend.  The last time I went, the get together was
on Friday and I missed it!  We have no firm plans as of yet.  Since we are
coming from NY (50 miles east of NYC on LI) we need time to travel.  I would
prefer attending over the long weekend (Sat thru Mon) if possible.

Mike

-----Original Message-----
From: rhodes22-list-bounces at rhodes22.org
[mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Art Czerwonky
Sent: Wednesday, September 18, 2013 9:43 PM
To: The Rhodes 22 Email List
Subject: Re: [Rhodes22-list] Center Board leak

Mike,

Will you be attending the show in Annapolis?  I am thinking that you and
others from fleet might like to get a picture with Stan or with one of the
display boats.  I will try to get a priceless photo of Stan as well, if he
can stand still long enough.  I got a picture of Stan with his daughter's
renewed O'Day in '06, might even be able to dig that one up.  

Also, do you or any know of a get-together lunch if on Friday or Saturday.
I remember the one the next year (remember Mary Lou dancing on the table
tops, oops) and was a lot of fun meeting everyone.  

Enough for now, my friend.

Best,

Art

"Michael D. Weisner" <mweisner at ebsmed.com> wrote:

>I always had to use 3M 4200 on the seal on my '81.  I too had a problem 
>with just the gasket - lots of leaks!  Maybe there was a problem with 
>the form that was used to make the CB trunk & cap in those days.
>
>Mike
>s/v <-- NoName -->  ('91)
>Nissequogue River, NY
>
>
>
>-----Original Message-----
>From: rhodes22-list-bounces at rhodes22.org
>[mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of rbeytagh
>Sent: Wednesday, September 18, 2013 1:24 PM
>To: rhodes22-list at rhodes22.org
>Subject: [Rhodes22-list] Center Board leak
>
>Wow....I just splashed my boat for the first time simply to see if the 
>new center board gasket I installed  was water proof. It 
>wasn't....water poured in as if there was nothing there. I tightened 
>all the screws but this only slowed down the in-flow a little. Stan is 
>adamant that no silicon should be used to seal the gasket, but apart 
>from this I can't figure a way to seal this. Any suggestions?
>
>Thanks
>Richard - S/V Waif
>Asheville NC
>
>
>
>--
>View this message in context:
>http://rhodes-22.1065344.n5.nabble.com/Center-Board-leak-tp46798.html
>Sent from the Rhodes 22 mailing list archive at Nabble.com.
>__________________________________________________
>To subscribe/unsubscribe go to
>http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>
>For the list Charter and help with using the mailing list and archives 
>go to http://www.rhodes22.org/list 
>__________________________________________________
>
>__________________________________________________
>To subscribe/unsubscribe go to 
>http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>
>For the list Charter and help with using the mailing list and archives 
>go to http://www.rhodes22.org/list 
>__________________________________________________

__________________________________________________
To subscribe/unsubscribe go to
http://www.rhodes22.org/mailman/listinfo/rhodes22-list

For the list Charter and help with using the mailing list and archives go to
http://www.rhodes22.org/list
__________________________________________________