[Rhodes22-list] Installing a hatch

[The Rhodes 22 Email List]

Bob:
Thanks for the info. Can you tell me the make and size of the hatches? Are
they metal or plastic? Are they installed directly on your cabin top or on a
built up collar of some sort?
Thanks,

Graham 


-----Original Message-----
From: rhodes22-list-bounces at rhodes22.org
[mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 22 Email
List
Sent: August-22-14 6:26 PM
To: The Rhodes 22 Email List
Subject: Re: [Rhodes22-list] Installing a hatch

Graham:  you don't say where you intend to place the hatch.  GB installs
adjacent the pop-top and parallel to the mast.  I believe most new boats
(and some re-cycled) have two installed.

Our 2010 had two installed as part of the build.  Very nice.

Bob on the "NoKaOi 3"

Sent from my iPad

> On Aug 22, 2014, at 10:07 AM, The Rhodes 22 Email List
<rhodes22-list at rhodes22.org> wrote:
> 
> I used a couple of Bomars that I found on eBay. I believe the factory 
> uses a plastic framed hatch when they recycle. This might be a better 
> option as they are more flexible than the aluminum frames.
> 
> Richard
> 
> 
> On Fri, Aug 22, 2014 at 12:27 AM, The Rhodes 22 Email List < 
> rhodes22-list at rhodes22.org> wrote:
> 
>> Thanks Richard. What make and model did you use?
>> 
>> Graham
>> 
>> -----Original Message-----
>> From: rhodes22-list-bounces at rhodes22.org
>> [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of The Rhodes 
>> 22 Email List
>> Sent: August-21-14 9:18 PM
>> To: The Rhodes 22 Email List
>> Subject: Re: [Rhodes22-list] Installing a hatch
>> 
>> You need a hatch around 18" square. Go ahead and just install 
>> it...the deck curvature is not significant enough to cause a problem. 
>> Be fairly generous with the 5200 on the leading edge. Make sure you 
>> install the internal trim before screwing everything down.
>> 
>> Cheers
>> Richard
>> S/V Waif R22
>> 
>> 
>> 
>> 
>> On Thu, Aug 21, 2014 at 8:58 PM, The Rhodes 22 Email List < 
>> rhodes22-list at rhodes22.org> wrote:
>> 
>>> Has anyone installed a hatch on the Rhodes 22? I would like to add 
>>> one to my boat but the cabin top has a curve and I am wondering how 
>>> others dealt with that. Was the hatch able to take the curve or did 
>>> you need to build up a collar for it.
>>> 
>>> Alternatively, Can someone tell me the setup for boats that had the 
>>> hatch installed at the factory?
>>> Thanks,
>>> 
>>> Graham
>>> 
>>> __________________________________________________
>>> To subscribe/unsubscribe go to
>>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>>> 
>>> For the list Charter and help with using the mailing list and 
>>> archives go to http://www.rhodes22.org/list 
>>> __________________________________________________
>> __________________________________________________
>> To subscribe/unsubscribe go to
>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>> 
>> For the list Charter and help with using the mailing list and 
>> archives go to http://www.rhodes22.org/list 
>> __________________________________________________
>> 
>> __________________________________________________
>> To subscribe/unsubscribe go to
>> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>> 
>> For the list Charter and help with using the mailing list and 
>> archives go to http://www.rhodes22.org/list 
>> __________________________________________________
> __________________________________________________
> To subscribe/unsubscribe go to 
> http://www.rhodes22.org/mailman/listinfo/rhodes22-list
> 
> For the list Charter and help with using the mailing list and archives 
> go to http://www.rhodes22.org/list 
> __________________________________________________

__________________________________________________
To subscribe/unsubscribe go to
http://www.rhodes22.org/mailman/listinfo/rhodes22-list

For the list Charter and help with using the mailing list and archives go to
http://www.rhodes22.org/list
__________________________________________________