[Rhodes22-list] Motor Lift Switch

[John Waldhausen]

All
I tried the below and when I hooked up the switch as written about below, it got ver hot and has fried all the receiver and now nothing works. Any suggestions?

John 
Bainbridge Island

> On Nov 7, 2015, at 4:07 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote:
> 
> The one Bruce refers to, I believe, is the one Stan installs.  If not, it is quite similar. 
> 
> Bob in Stuart, FL
> 
> Sent from my iPad
> 
>> On Nov 7, 2015, at 4:15 PM, The Rhodes 22 Email List <rhodes22-list at rhodes22.org> wrote:
>> 
>> Ted,
>> 
>> That's not the one I used.  Here's mine:
>> http://www.gamainc.com/site/epage/130244_941.htm.
>> 
>> As for wiring, there's a red and a white wire from the boat battery to a
>> block (which is the receiver for the remote)  located on the port side of
>> the lazarette near the winch and then wires from the block to the winch. 
>> Remove the ones from the block/controller that lead to the winch.  Add one
>> wire from the red side of the block to the connector in the middle of the
>> switch on the side that has a label, and wire the white side of the block to
>> the other center pole on the switch.  Then run wires from the remaining two
>> poles on the switch to the terminals on the winch.  It doesn't make any
>> difference which of those wires to which terminal, but if after installing
>> the switch in the lazarette bulkhead the motor goes down when you push the
>> up side of the rocker, then simply swap those last two wires on the back of
>> the switch.
>> 
>> Alternatively, I think you could disconnect the wires from the remote
>> controller, and connect them directly to the switch with some added wire,
>> bypassing the remote controller entirely.  
>> 
>> When cutting a square hole to insert the switch, err on the side of too
>> small and sand your way to the "right size."   The spec says the switch is
>> .83" x 1.48" and I thought that was the size I cut.  Fortunately, whatever I
>> cut was too small and I just kept enlarging it in increments until the
>> switch snapped into place.  If you cut too large, the switch won't mount
>> properly -- it's held in by tensioners on the side of the switch.
>> 
>> In the meantime, put a float on the remote.  At least you'll have a chance
>> if you lose it overboard before you get the switch installed.  
>> 
>> By the way, I don't know if you keep the remote controller hooked in the
>> circuit what would happen if you tried to use the remote.  Maybe both the
>> switch and the remote would work at your option, but then maybe neither
>> would work.  Somebody who actually understands electricity might be able to
>> advise on that.
>> 
>> Hope that helps.  Good luck.
>> 
>> Bruce
>> s/v Tuxedo
>> 
>> 
>> 
>> --
>> View this message in context: http://rhodes-22.1065344.n5.nabble.com/Motor-Lift-Switch-tp51213p51218.html
>> Sent from the Rhodes 22 mailing list archive at Nabble.com.
>> __________________________________________________
>> To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list
>> 
>> For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list
>> __________________________________________________
> 
> __________________________________________________
> To subscribe/unsubscribe go to http://www.rhodes22.org/mailman/listinfo/rhodes22-list
> 
> For the list Charter and help with using the mailing list and archives go to http://www.rhodes22.org/list
> __________________________________________________