[Rhodes22-list] recognize part

[Graham Stewart]

I doubt very much that the pin would hold without going through a hole.

Graham Stewart
gstewart8 at cogeco.ca


-----Original Message-----
From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Cary Tolbert
Sent: Monday, July 27, 2020 10:01 PM
To: The Rhodes 22 Email List
Subject: Re: [Rhodes22-list] recognize part

Thanks Graham. Using a r clip did cross my mind. Though  I did not think of
drilling a hole.

On Mon, Jul 27, 2020, 9:57 PM Graham Stewart <gstewart8 at cogeco.ca> wrote:

> That clip broke off on my boat years ago. I drilled a hole in the pin on
> the pintel about 1/2 inch below the bottom of the gudgeon. I then slid a
> piece of tubing (gas line, I think) up to the bottom of the gudgeon and
> inserted a R clip through the hole. The purpose of the tube was to provide
> some cushion for the fixtures.
>
> Graham Stewart
> Agile, Rodes 22, 1976
> Kingston Ontario
>
>
> -----Original Message-----
> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf
> Of Cary Tolbert
> Sent: Monday, July 27, 2020 12:10 PM
> To: The Rhodes 22 Email List
> Subject: Re: [Rhodes22-list] recognize part
>
> Thanks Mike. For once it seems the Rhodies are in agreement. I shall mark
> this day on my calendar
>
>
> On Mon, Jul 27, 2020, 12:06 PM Mike Riter <mike at traildesign.com> wrote:
>
> > Cary, Here's a photo of what it is and where mine is located on my R22.
> > Since it doesn't make good contact with the indent in the gudgeon, GB
> > installed the hose and clamp to help hold the rudder in place.
> >
> >
> > Michael Riter
> > SV Emma B
> >
> >
> >
> > On Mon, Jul 27, 2020 at 10:05 AM Cary Tolbert <retiredtoby at gmail.com>
> > wrote:
> >
> > >
> > >
> > > Sent from Mail for Windows 10
> > > I think this a portion of the retainer clip for the rudder. Could
> anyone
> > > send me a photo of the total part and what position it has on the
> rudder.
> > > Have not found anything at marine part retailers that is even close.
> > >
> > > Secondly, I need to replace my impeller on my motor. I have watched you
> > > tube and have a general knowledge of the project. Does anyone care to
> > share
> > > what to watch out for , things to think about in advance. In general
> what
> > > are the pitfalls?
> > >
> > > Thanks,
> > > Cary Tolbert
> > > S/V Whisper ‘86
> > >
> > > -------------- next part --------------
> > > A non-text attachment was scrubbed...
> > > Name: DSCN6451.JPG
> > > Type: image/jpeg
> > > Size: 2127493 bytes
> > > Desc: not available
> > > URL: <
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20200727/be2c40c0/attachment.jpe
> > > >
> > > -------------- next part --------------
> > > A non-text attachment was scrubbed...
> > > Name: DSCN6450.JPG
> > > Type: image/jpeg
> > > Size: 3776361 bytes
> > > Desc: not available
> > > URL: <
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20200727/be2c40c0/attachment-0001.jpe
> > > >
> > >
> > -------------- next part --------------
> > A non-text attachment was scrubbed...
> > Name: IMG_0589.JPG
> > Type: image/jpeg
> > Size: 654819 bytes
> > Desc: not available
> > URL: <
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20200727/e28bc5c7/attachment.jpe
> > >
> >
>
>