[Rhodes22-list] Problem with furler

[Mary Lou Troy]

We used to use Sailkote on the edges of the mast slot as high as we 
could reach, or the whole slot if the mast was down. Sailkot will not 
attract dirt or discolor the sail.

No bearings in the main furler unless someone tinkered with it.

Mary Lou

ex R22
now Rosborough RF-246

On 6/10/2020 8:50 AM, Lowe, Rob wrote:
> Allyn,
> Glad to hear you made progress with your furler.  I'd put a new one on your Christmas list.  Maybe Santa will bring you one this year.  He brought me a new one a couple of years ago and this year he brought me a new main.
>
> I'm not sure there are any bearings in the main.  I've got to install my new main later on this week so I'll let you know what I find.  I know there are some things you can do to make it furl easier.  I believe a good dose of Sailkote in on the furling mechanism and the slot in the boom are good places to start.
>
> Did you get your frayed line figured out?
>
> Rob
>
> ________________________________
> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of Allyn Baskerville <allynb at adsne.com>
> Sent: Tuesday, June 9, 2020 11:03 PM
> To: The Rhodes 22 Email List <rhodes22-list at rhodes22.org>
> Subject: Re: [Rhodes22-list] Problem with furler
>
> Rob, thanks for the response. You have given me some great pointers.
>
> I was able to fix the issue thanks to someone in the boat club being familiar with the CDI furlers. Apparently, bearings have a tendency of falling out when the boats are transported, and I’m pretty sure at this point in time the bearings were always out since I purchased the boat.
>
> All we had to do is lift the furler assembly right above the drum which lifts out the internal drum piece, extract the loose bearings, lift the cup that should surround the bearings, replace the bearings on the race (more in this in a moment), drop the cup over the bearings, and drop the furler assembly. I didn’tHave to remove any rigging or drop the headsail. Everything is held together with gravity.
>
> I was able to get the bearings to stick to the race using some red grease. Grease is not normally used here, but it worked. I had a dream the very night I used the red grease how card stock and tape could be used to hold the bearings without grease the next time.
>
> I was able to extract 6 bearings. CDI said there should be 7, so I need to purchase another bearing or set of bearings.  The headsail furls so incredibly easily now. It’s never worked this well, though it’s one beating short.
>
> I’m curious now. The headsail furls so easily now, that I wonder if the mainsail furler needs some work. I’ve always felt as if I’ve fought it. Are there bearings that could fall out of the mainsail furler?
>
> One parting comment. I love the boat. I went from a Dolphin, to a Hobie 18, to the Rhodes. We’re sailing in 2 minutes, we’re packed up in 2 minutes, don’t have to bring out and fold up the sails, and I gets *lots* of comments from others at the club about how much they like the boat. This boat really makes sailing fun.
>
> Sent from my iPhone
>
>> On Jun 4, 2020, at 11:32 AM, Lowe, Rob <rlowe at vt.edu> wrote:
>>
>> Allyn,
>> If your furling line parts your forestay will not be effected.  But you won't be able to furl your head sail.  You can furl it by hand if you really need to, but that's difficult in a strong wind and it means you have to put your hands on the sail and wrap it up.  You can replace the furling line with headsail up, but it's a mental challenge.  You would untie the knot on the top of your furling drum and feed that line down and and remove it and replace the line.  The challenge there is to get the line running in the right direction around the drum (make note of how yours is now) before you remove it.  The line wraps up around the drum as the sail is unfurled and it took me a while to get my head around that.  You also need to get it so there are a few turns left on the drum when the sail is furled. If the separation is right near the end of the line (hard to tell from the photo), you might be able to grab that knot, pull up on it until the separation is outside the drum and re-knot it if your furling line is long enough. - rob
>>
>> ________________________________
>> From: Rhodes22-list <rhodes22-list-bounces at rhodes22.org> on behalf of Allyn Baskerville <allynb at adsne.com>
>> Sent: Wednesday, June 3, 2020 11:41 PM
>> To: rhodes22-list at rhodes22.org <rhodes22-list at rhodes22.org>
>> Subject: [Rhodes22-list] Problem with furler
>>
>> I have a 2001 Rhodes and noticed tonight the furler is separating and the line is cut party through. Is there a risk of the forestay coming loose? I was planning on sailing tomorrow, but I won’t if this is dangerous. I’ve not taken one of these apart before, but I’m concerned I’ll have real problems on my hand if this isn’t fixed ASAP.   Thanks
>>
>> [cid:CB4F023F-7409-442D-8399-5701822AE53D]
>>
>> Sent from my iPhone
>> -------------- next part --------------
>> A non-text attachment was scrubbed...
>> Name: IMG_0329.jpg
>> Type: image/jpeg
>> Size: 276178 bytes
>> Desc: IMG_0329.jpg
>> URL: <http://rhodes22.org/pipermail/rhodes22-list/attachments/20200604/376d369a/attachment.jpg>



-- 
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus