[Rhodes22-list] cutting mast step heldyard organizer

[Richard Stott]

What organizer?
Where does that thing go again?

On Long Island, its an auganiza.

Dadventure
Richard Stott, AIA, LEED AP 
www.stottarchitecture.com
Office	631-283-1777
Cell		516-965-3164 





> On Nov 19, 2020, at 9:44 AM, Graham Stewart <gstewart8 at cogeco.ca> wrote:
> 
> Yea. Right. Thanks Ric. I thought I must have had  something in mind when I got the organizer. I just have to remember now where I put your message when it comes time to rig it.
> 
> Graham Stewart
> gstewart8 at cogeco.ca
> ---------------------------------------------------------------------------------
> I use the free version of Spam Reader to get rid of spam. The Professional version doesn't have this disclaimer in outgoing emails. 
> Try Spam Reader (http://www.spam-reader.com) for free now!
> 
> -----Original Message-----
> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Ric Stott
> Sent: Thursday, November 19, 2020 8:15 AM
> To: The Rhodes 22 Email List
> Subject: Re: [Rhodes22-list] cutting mast step heldyard organizer
> 
> Hey Graham
> Besides feeling organized and yachtly,
> I think you were going to attach a boom bang to that thing and maybe a Cunningham too eh?
> Ric
> Dadventure. 
> 
> Sent from my iPhone
> 
>> On Nov 18, 2020, at 8:17 PM, Graham Stewart <gstewart8 at cogeco.ca> wrote:
>> 
>> Jesse: 
>> At the time I bought it I had a clear idea of how I planned to use the organizer but now I can't remember what it was. I ordered a sail pac and I think I wanted to run lines back to the cockpit and didn't want to bolt any hardware to the deck that could be avoided. Maybe it will all come back to me when I launch next spring. On the other hand, by that time I might not remember my name. 
>> 
>> Graham Stewart
>> gstewart8 at cogeco.ca
>> 
>> 
>> -----Original Message-----
>> From: Rhodes22-list [mailto:rhodes22-list-bounces at rhodes22.org] On 
>> Behalf Of Jesse Shumaker
>> Sent: Tuesday, November 17, 2020 7:44 PM
>> To: The Rhodes 22 Email List
>> Subject: Re: [Rhodes22-list] cutting mast step heldyard organizer
>> 
>> Nice work Graham, thanks for sharing.  Just curious, how are you 
>> planning to use your organizer?  I installed mine last week as part of 
>> changes or the rigging to emulate some of Peter's setup.  Fortunately 
>> the one I ordered only had the tabs on port and starboard so I didn't 
>> have to cut anything off.
>> 
>> Jesse Shumaker
>> S/V Zephyr
>> 
>>> On Tue, Nov 17, 2020 at 6:11 PM Graham Stewart <gstewart8 at cogeco.ca> wrote:
>>> 
>>> A few months back there was a discussion about halyard mast-step 
>>> organizers and whether one needed to go to a machine shop to remove 
>>> one of the tabs. I had already bought an organizer with the extra tab 
>>> at the front and did not fancy paying as much to have the ta cut off 
>>> as the item cost in the first place.
>>> 
>>> Today I set about to see if I could cut it off with my home tools. As 
>>> it turned out it was pretty easy. I used my cordless Ryobi 
>>> reciprocating saw
>>> (20V) with a fresh metal cutting blade and had no trouble cutting off 
>>> the tab. I then dressed the edge with my bench grinder and finished 
>>> it off with a hand file. Given that the stainless steel was 1/8" 
>>> thick I was surprised that it went so easily. Maybe the steel was 
>>> poor quality. For what it is worth...
>>> 
>>> Graham Stewart
>>> Agile, Rodes 22, 1976
>>> Kingston Ontario
>>> 
>>> 
>> 
>