[Rhodes22-list] Tiller-Outboard Interconnect question

[Rick Lange]

I have a tiller on my outboard that I use to steer with the motor,
especially when backing up in a tight spot.  But I prefer to sit forward in
the cockpit, so I use a tiller extension that allows me to do that.  The
extension clamps onto the end of the motor tiller and the clamp connects to
the extension bar with a universal joint.

Regards,

Rick Lange


On Fri, Jan 21, 2022 at 10:06 AM ROGER PIHLAJA <roger_pihlaja at msn.com>
wrote:

> Bob & Jeff,
>
> The fastest way to make your Rhodes 22 turn a corner under power does not
> involve the tiller-outboard connecting linkage.
>
> Assume you want to make a hard turn to port in the minimum possible area.
> You setup by motoring along  slowly, say 2-3 knots, just enough speed to
> maintain rudder steering control.  Put the desired slip about 1 boat length
> away to port.  Assume you are going for a port side docking against a
> finger pier.  Shift the motor into neutral and turn the motor’s tiller all
> the way the port.  When your bow is even with the end of the finger pier,
> do the following in quick succession.  Shift into reverse, apply full
> throttle, and put the boat tiller hard over.  Hang on to something!  The
> boat will yaw 90 deg to port in about 1 sec!  It will simultaneously slow
> down, side slip about 1/3 boat length to starboard, and drift forward about
> ¾ boat length.  At about 45 deg of yaw, throttle the motor back to idle and
> then shift into neutral.  Straighten out the outboard tiller and the boat
> tiller.  The boat’s rotational inertia will complete the 90 deg of yaw.
> Note, the hull and shoal draft keel produce a lot of drag vs. yawing.  The
> boat will use up it’s rotational inertia very quickly.  With a little bit
> of practice, you will end up virtually stopped at the entrance to the slip,
> with your bow pointed into the slip, and about 12 inches of clearance
> between your port side rub rail and the pier.  Now shift into forward and
> idle into your slip.   For a starboard quick turn, simply turn the motor
> tiller to starboard before shifting into reverse.
>
> This technique is also very useful to force the bow to yaw into strong
> cross wind &/or cross current.  It’s also very useful for a stern to
> docking.
>
> It’s best to practice this maneuver in open water a few time before
> attempting it in a crowded marina.  You will be impressed with how much
> faster the boat will yaw when the motor is simultaneously applying sideways
> and reverse thrust to the transom.  Obviously, the tiller-outboard
> connecting linkage cannot be connected to execute this maneuver.
>
> Try this technique, it will make you look like a docking genius!
>
> Roger Pihlaja
> S/V Dynamic Equilibrium
>
> Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows
>
> From: Bob Garrant<mailto:bgarrant at gmail.com>
> Sent: Friday, January 21, 2022 5:43 AM
> To: The Rhodes 22 Email List<mailto:rhodes22-list at rhodes22.org>
> Subject: Re: [Rhodes22-list] Tiller-Outboard Interconnect question
>
> That’s what I’m looking for. My slip is in a corner so i only have 90° To
> maneuver in rather than 180°. So every little bit helps.
> I appreciate all the guidance from those way more experienced than I am
> with this vessel.
> Bob
>
> On Fri, Jan 21, 2022 at 7:10 AM Jeff Smith Photo <jeffsmithphoto at gmail.com
> >
> wrote:
>
> > I use the connection to my Yamaha 8 only when approching the mooring or
> > dock.  It enables me to make a tighter more controlled turn.
> >
> > Best Regards
> > Jeff Smith
> >
> https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.http%2F%2FJeffSmithPhoto.Net&data=04%7C01%7C%7Cdc137de0632540da681f08d9dce3f043%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637783693819652051%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&sdata=yE3ddR9mO8DtUj0wCb6ybevj3YcjJisBjuaqi0lT6JY%3D&reserved=0
> > 732-236-1368
> >
>
>