[Rhodes22-list] Pop top enclosue

[recorderguy2001 at yahoo.com]

Thanks Roger,
 I'll try this method and post how it goes. 

Peter     On Sunday, May 28, 2023, 12:16:38 PM EDT, ROGER PIHLAJA <roger_pihlaja at msn.com> wrote:  
 
 <!--#yiv9255478856 filtered {}#yiv9255478856 filtered {}#yiv9255478856 filtered {}#yiv9255478856 p.yiv9255478856MsoNormal, #yiv9255478856 li.yiv9255478856MsoNormal, #yiv9255478856 div.yiv9255478856MsoNormal {margin:0in;font-size:11.0pt;font-family:"Calibri", sans-serif;}#yiv9255478856 a:link, #yiv9255478856 span.yiv9255478856MsoHyperlink {color:blue;text-decoration:underline;}#yiv9255478856 p.yiv9255478856msonormal, #yiv9255478856 li.yiv9255478856msonormal, #yiv9255478856 div.yiv9255478856msonormal {margin-right:0in;margin-left:0in;font-size:11.0pt;font-family:"Calibri", sans-serif;}#yiv9255478856 .yiv9255478856MsoChpDefault {}#yiv9255478856 filtered {}#yiv9255478856 div.yiv9255478856WordSection1 {}-->
Peter,

  
 
Keep in mind that I have an older pop top that may not be exactly like yours:

  
 
Start with the pop top up and the companionway sliding hatch closed

  
 
The pop top enclosure front zipper should be open and “unhitched” and the companionway zippers should be open

  
 
The pop top enclosure should drop over the pop top

  
 
Zip up the front zipper and fasten the snaps on the front of the enclosure

  
 
Make certain the pop top enclosure is hanging evenly on both sides and pull aft on the top of the nclosure to make certain all the slack is out of the top of the enclosure

  
 
Working from front to back, fasten the snaps on the sides of the enclosure

  
 
Fasten the snaps at the rear of the enclosure

  
 
Finally, close the zippers on the companionway hatch.

  
 
When the fabric is cold, it tends to be pretty stiff.  But, you can pull fairly hard on it without ripping.  Try putting it on when it’s a hot day and it will stretch more easily.  Once the fabric has stretched, it will be easier to install.  Try using a blow dryer to warm the fabric to get it to stretch initially.

  
 
Roger Pihlaja

S/V Dynamic Equiibrium

  
 
  
 
  
 
Sent from Mail for Windows

  
 
From: recorderguy2001 at yahoo.com
Sent: Sunday, May 28, 2023 6:27 AM
To: The Rhodes 22 Email List;ROGER PIHLAJA
Subject: Re: [Rhodes22-list] Pop top enclosue

  
 

Hi Roger,
The snaps seem to line up ok, it's just that when I attach one side I find the other is a couple of inches shy of reaching. I may just be a little timid about stretching the fabric, or perhaps it's too stiff. Does it matter where the slider sits on the pop-top? I'm assuming that there's no way my pop-top could be up too high as the legs are in the detents as is the mast slider. I was wondering if there was a trick such as attaching the bow and stern snaps before the side snaps that make it easier to get it on.
By the way, I've been meaning to thank you for posting all of your guides for the boat. I used your " how to fold the pop top enclosure " guide yesterday (there's a copy in the boat) and your rig tuning guide was extremely helpful (also on the boat). Undoubtedly I'll be referring to more of your posts as I get further into Rhodes ownership.

Peter 
 
On Sunday, May 28, 2023, 08:27:44 AM EDT, ROGER PIHLAJA <roger_pihlaja at msn.com> wrote:
 
  
 
  
 
Peter,
 
 
 
When you say, “Mine doesn’t go on easily”, what do you mean?  Does the enclosure not fit well over the pop top, or do the female snaps on the enclosure not line up with their corresponding male snaps on the cabin roof, or is the enclosure so stiff that it’s difficult to use, or?  My (well used) pop top enclosure goes on or off in a couple of minutes without any particular drama.  Many years ago, I published a series of photos to the Rhodes 22 website that illustrates a good way to fold the enclosure.
 
 
 
Roger Pihlaja
 
S/V Dynamic Equilibrium
 
 
 
Sent fromMail for Windows
 
 
 
From:Peter via Rhodes22-list
Sent: Saturday, May 27, 2023 7:38 PM
To: rhodes22-list at rhodes22.org
Subject: [Rhodes22-list] Pop top enclosue
 
 
 
Does anyone have any tricks or advise regarding the installation of the pop top enclosure?  Mine doesn't go on easily and I don't want to force it.

Thanks
    Peter