[Rhodes22-list] Problem shrouds = location of answer for David

[Brad Haslett]

Another red letter day!  Bill Effros makes perfect sense!

Rummy, sometimes I wish you weren't so shy and would just speak your mind.

This discussion reminds me of my days as an apprentice aircraft mechanic.  I
asked my boss why we weren't using a torque wrench on whatever we were
working on.  He said, "oh yeah, go get one".  I checked his work and most
were very, very close to correct.  He said, "go get the other one and check
again".  They were still very close but also different.  Then he said,
"trust me kid, it's hard to beat a man at his own craft".

I asked the guy who stepped the mast and rigged my boat (the same guy who
delivered it) if I needed to borrow a loos guage.  He rolled his eyes and
said, who has one you can trust?

Simple is sometimes the best method.

Brad


On 6/24/06, Bill Effros <bill at effros.com> wrote:
>
> Oh, please...
>
> This is like a discussion of how hard to slam a car door.  You only have
> to slam it hard enough to close.  The car can take a harder slam, but
> you are not accomplishing anything good for the car by slamming the door
> harder.
>
> We should banish Loos gauges from this list.  They are supposed to be
> calibrated for the type and size of stay they are measuring.  They don't
> measure in pounds--you interpolate index numbers.
>
> Where the hell did 200 pounds come from, anyhow?
>
> Is that 200 pounds when the other 8 shrouds are slack, or 200 pounds
> when the other 8 shrouds also each show 200 pounds?  Or is it 200 pounds
> total, divided by 9 shrouds?
>
> The tension on the back stay which holds up the traveler is supposed to
> be the same as the tension on the lower side stays?
>
> If the mast is not perpendicular to the boat, but all the stays register
> 200 pounds--is the rigging ok?
>
> A little knowledge is a dangerous thing.
>
> Bill Effros
>
>
>
> TN Rhodey wrote:
> > Ed,
> >
> > Without a gauge it is hard to quantify hand tight. Perhaps someone
> > should tighten hand tight and then measure? What if three people
> > tightned hand tight and measured? I bet you would have 3 different
> > measurements. I must admit that mine are tighter than hand
> > tight....not much. Lee side shrouds still go slack. Sloppy or over
> > tight, either way creates proplems.
> >
> > Roger knew how tune an R22 and he used a gauge. Did you see his specs?
> > Anyone with IMF actually use a gauge? Someone should know this? I may
> > have to borrow a friend's gauge and measure .....
> >
> > Wally
> >
> >
> >> From: Tootle <ekroposki at charter.net>
> >> Reply-To: The Rhodes 22 mail list <rhodes22-list at rhodes22.org>
> >> To: rhodes22-list at rhodes22.org
> >> Subject: [Rhodes22-list] Problem shrouds = location of answer for David
> >> Date: Sat, 24 Jun 2006 07:03:38 -0700 (PDT)
> >>
> >>
> >> David:
> >>      I would like to suppliment Captain Rummy's response to you with
> >> where
> >> you find documentation supporting what he is telling you.  Stan, aka,
> >> General Boats, makes an instruction manual for the Rhodes 22.  With
> >> Rose's
> >> permission, a copy of which is located in the Document Library of
> >> this web
> >> site. See:
> >>
> >> http://www.rhodes22.org/doclib/Rhodes22-1988-Owners-Raven.pdf
> >>
> >>       Now specifically go to pages 4 and 5, especially about the guy
> who
> >> used pliers to tighten the shrouds.  So after reading the instructions
> >> promulgated by Stan you may begin to understand why most of use just
> >> follow
> >> his instuctions.  Please understand that while Stan's education is
> >> electrical engineering he is a nautical engineer by advocation.  The
> >> point
> >> Rummy made is that the mast is not made to be over tighened.  What
> Rummy
> >> said is supported by the instructional manual for this boat.
> >>       Who ever told you to use 200 pounds of tension told you very
> >> wrong.
> >> That kind of number may be correct for a fifty foot keel stepped racing
> >> sailboat, but not appropriate for a cabin (deck) stepped mast without a
> >> compression post from base to keel.   It sounds like somebody has
> >> created a
> >> problem in over tensioning the stays.  Hopefully the cabin is not
> >> reshaped
> >> permenantly.
> >>        Many Cat boats and other modern designs do not even use stays
> >> to keep
> >> the mast upright.  Read about the latest model Hunter sail boats.
> >>
> >> Ed K
> >> Greenville, SC, USA
> >> --
> >> View this message in context:
> >> http://www.nabble.com/Problem-shrouds.-t1840793.html#a5025664
> >> Sent from the Rhodes22 forum at Nabble.com.
> >>
> >> __________________________________________________
> >> Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list
> >
> >
> > __________________________________________________
> > Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list
> >
> __________________________________________________
> Use Rhodes22-list at rhodes22.org, Help? www.rhodes22.org/list
>