[Rhodes22-list] Need to replace Hatch

[JbTek]

ya, I use that 1 to hold my beer, inside & out. My compass sits on it also.
Have not used the table yet.
Jb
----- Original Message ----- 
From: "Michael D. Weisner" <mweisner at ebsmed.com>
To: "The Rhodes 22 Email List" <rhodes22-list at rhodes22.org>
Sent: Wednesday, February 25, 2009 10:18 AM
Subject: Re: [Rhodes22-list] Need to replace Hatch


> Jb,
>
> It's the thinner leg.  The thick one fits the main table which can be
> erected in the rear of the cockpit or slightly to the port side of the
> cabin.
>
> Glad to help.
>
> Mike
> s/v Shanghai'd Summer ('81)
> Nissequogue River, NY
>
> From: "JbTek" Wednesday, February 25, 2009 12:01 PM
> >I have 1 of those rolling aroud under my seat. Now I know what its for.
> > Jb
> > ----- Original Message ----- 
> > From: "Michael D. Weisner" <mweisner at ebsmed.com>
> > To: "The Rhodes 22 Email List" <rhodes22-list at rhodes22.org>
> > Sent: Wednesday, February 25, 2009 9:15 AM
> > Subject: Re: [Rhodes22-list] Need to replace Hatch
> >
> >
> >> Rob,
> >>
> >> It was Stanley standard equipment back in 1981.  The leg is aluminum
with
> > a
> >> rubber stopper foot and the top fits into a wooden circular retainer in
> > the
> >> underside of the table (originally the outside top of the hatch door.)
> >>
> >> Mike
> >> s/v Shanghai'd Summer ('81)
> >> Nissequogue River, NY
> >>
> >> From: "Lowe, Rob" Wednesday, February 25, 2009 8:37 AM
> >> > Mike,
> >> > Tell me a bit more about this table leg if you will.  Something you
> >> > rigged up yourself? - rob
> >> >
> >> >
> >> > -----Original Message-----
> >> > From: rhodes22-list-bounces at rhodes22.org
> >> > [mailto:rhodes22-list-bounces at rhodes22.org] On Behalf Of Michael D.
> >> > Weisner
> >> > Sent: Tuesday, February 24, 2009 10:22 PM
> >> > To: The Rhodes 22 Email List
> >> > Subject: Re: [Rhodes22-list] Need to replace Hatch
> >> >
> >> > Greg,
> >> >
> >> > Welcome to the R22 list and congratulations on your new project.
> >> > Hopefully
> >> > you will find some time to actually sail her.
> >> >
> >> > Most of us have replaced our plywood hatches at least once.  I am on
my
> >> > third wooden one on my '81.  After replacing the teak veneer plywood
> >> > version
> >> > twice with the same, I found that one could do a better job with
birch
> >> > veneer, stained and finished with spar varnish.  The varnish stands
up
> >> > to
> >> > the weather much better than the teak veneer ever did.  I also have a
> >> > version made of white 1/2 inch "starboard", a fairly expensive nearly
> >> > indestructible composite material that doesn't look as nice as the
> >> > stained
> >> > wood, in my opinion.
> >> >
> >> > The hinge not only kept the two pieces together in storage but also
> >> > permitted the hatch to be folded at an angle (almost 90 degrees) so
> >> > that
> >> > the
> >> > upper portion was supported by a leg to the cockpit floor, to
function
> >> > as a
> >> > serving table from the galley.  If you do not desire this, there is
no
> >> > reason why it couldn't be two pieces.
> >> >
> >> > Mike
> >> > s/v Shanghaid'd Summer ('81)
> >> >       Nissequogue River, NY
> >> >
> >> > __________________________________________________
> >> > To subscribe/unsubscribe or for help with using the mailing list go
to
> >> > http://www.rhodes22.org/list
> >> > __________________________________________________
> >> >
> >> >
> >>
> >> __________________________________________________
> >> To subscribe/unsubscribe or for help with using the mailing list go to
> > http://www.rhodes22.org/list
> >> __________________________________________________
> >
> > __________________________________________________
> > To subscribe/unsubscribe or for help with using the mailing list go to
> > http://www.rhodes22.org/list
> > __________________________________________________
> >
>
> __________________________________________________
> To subscribe/unsubscribe or for help with using the mailing list go to
http://www.rhodes22.org/list
> __________________________________________________