[Rhodes22-list] Inner Shroud Issues

[Matt Wilson]

Thanks Todd, would you mind trying to send those last 3 images another way?

Matt

On Thu, Nov 9, 2023 at 12:14 PM Todd Tavares <tavares0947 at gmail.com> wrote:

> I should add, that the reason for dry fitting, drilling the holes first,
> etc was so the installation of each could be done in one operation.
> The first coat of epoxy I put on the reinforcing plates/boards was slightly
> thinned with acetone attempting to get more penetration. When the first
> coat was still green and not fully set, I added the second coat and also
> wetted out the cabin wall panel. And finally I added the thickened epoxy,
> reinforcing plate, and chainplate before the other epoxy had cured.
>
> I did learn, that I had to use a lot more of the West System 406 thickener
> to get the described peanut butter consistency, than I had figured.
>
> So there are a few different ways to approach your particular repair. I'd
> suggest pulling the hatch out first and then decide.
>
> Good luck.
>
> Todd T.
>
> On Thu, Nov 9, 2023, 12:39 PM Matt Wilson <mwhornblower at gmail.com> wrote:
>
> > Thanks Todd for your help and diagram.  How many more sails till this
> pulls
> > apart?  ;)
> >
> > Can I get by by attaching two metal plates above and below the deck after
> > resealing to keep moisture out or is it too compromised already? the
> plates
> > would the fiberglass mess.  I am just a casual lake sailor so I'm not
> sure
> > how much I want to get into this kind of project.
> >
> > Have you or anyone else on the list done this repair?  I'm a total newbie
> > to this kind of project.
> >
> > Matt W
> >
> > On Thu, Nov 9, 2023 at 11:15 AM Todd Tavares <tavares0947 at gmail.com>
> > wrote:
> >
> > > Matt,
> > >
> > > You may have no choice but to pull the hatch; which will aid in the
> > repair,
> > > replace the core, epoxy, glass etc.
> > >
> > > This quick sketch doesn't account for the hatch being so close to the
> > > chainplate but it shows how the cabintop is constructed.
> > >
> > >
> > > Todd T
> > >
> > > On Thu, Nov 9, 2023, 12:03 PM Todd Tavares <tavares0947 at gmail.com>
> > wrote:
> > >
> > > > Matt,
> > > >
> > > > There is a right way which involves a ton of work, and there is an
> > > > adequate way.
> > > > The hard way is cutting away the cabin top removing any loose, wet,
> > > rotted
> > > > or dry rotted core material. Then epoxy in new plywood core, re-glass
> > the
> > > > cabin top, fair paint.
> > > > The alternative is to cut an access hole in the cabin wall. (Cut the
> > > > chainplate with a die grinder to pull it out from above or leave it
> in
> > > > place). Then put the chainplate on the outside of the cabin wall and
> a
> > > > backing plate inside.
> > > >
> > > > But looking at your pics, you may have no alternative that to cut
> away
> > > the
> > > > cabintop.
> > > >
> > > > Todd T.
> > > >
> > > > PS. I'll try to make a couple of pencil sketches so you know what is
> > > > inside.
> > > >
> > > > On Thu, Nov 9, 2023, 11:30 AM Matt Wilson <mwhornblower at gmail.com>
> > > wrote:
> > > >
> > > >> Hello everyone,
> > > >>
> > > >> I am asking for guidance on my current issues with the forward inner
> > > >> shrouds.  It appears someone had over tightened them in the past and
> > > made
> > > >> some attempts to shore them up.  I will include pictures oif what is
> > > going
> > > >> on from below and topside.  My question is is this something I
> > > >> should completely rework or should I only make attempts to keep
> water
> > > out
> > > >> by sealing up the deck around them?
> > > >>
> > > >> Many thanks for your help,
> > > >> Matt Wilson
> > > >> Hornblower II
> > > >> White Bear Lake, MN
> > > >>
> > > >>
> > > >>
> > >
> >
> https://mail.google.com/mail/u/0?ui=2&ik=67ba79a2ab&attid=0.1&permmsgid=msg-f:1782103858061391360&th=18bb4e04549a3600&view=att&disp=safe
> > > >>
> > > >>
> > > >>
> > >
> >
> https://mail.google.com/mail/u/0?ui=2&ik=67ba79a2ab&attid=0.3&permmsgid=msg-f:1782103858061391360&th=18bb4e04549a3600&view=att&disp=safe
> > > >>
> > > >>
> > > >>
> > >
> >
> https://mail.google.com/mail/u/0?ui=2&ik=67ba79a2ab&attid=0.5&permmsgid=msg-f:1782103858061391360&th=18bb4e04549a3600&view=att&disp=safe
> > > >>
> > > >>
> > > >>
> > >
> >
> https://mail.google.com/mail/u/0?ui=2&ik=67ba79a2ab&attid=0.7&permmsgid=msg-f:1782103858061391360&th=18bb4e04549a3600&view=att&disp=safe
> > > >>
> > > >
> > > -------------- next part --------------
> > > A non-text attachment was scrubbed...
> > > Name: 20231109_121109.jpg
> > > Type: image/jpeg
> > > Size: 967576 bytes
> > > Desc: not available
> > > URL: <
> > >
> >
> http://rhodes22.org/pipermail/rhodes22-list/attachments/20231109/6e3ab441/attachment.jpg
> > > >
> > >
> >
>