|
|
|
1
Gary Sanford demonstrates the old style GB mast raising system |
2
After attaching the hoist, mast, forward lowers and upper shrouds to
the boat and aft lowers to the hoist, begin hoisting |
3
Hoist quickly but smoothly |
4
Attach the head stay |
5
Disconnect the mast hoist |
|
Power distribution panel |
Main battery installation |
Secondary battery installation under settee |
The correct procedure for rafting:
1) determine who puts out bumpers
2) center boat sets an anchor
3) add boats one at a time
4) have a party! |
 ChickieBabe
mast stowed for quick deployment. Note the use of bungies to keep aft lower
and upper shrouds attached and under control. Mast raising system secured
in place. |
 John
Ward tests his inflatable PFD |
Beautiful Delta anchor roller installation. Owner?? (sorry, I've misplaced
this information) |
Close-up of the anchor roller |
Overhead of roller installation |
Cushion straps, Bill and Sandy Gallant |
Cushion straps, Bill and Sandy Gallant |
Friction control for tiller, Bill and Sandy Gallant |
Clip for managing excess outhaul line, Bill and Sandy Gallant |
Map table gudgeons |
Sheet stow bag |
V-berth extension over head, Bill and Sandy Gallant. Extra
large version |
Connector for V-berth extension, Bill and Sandy Gallant. Extra
large version |
V-berth extension in the 'up' position, Bill and Sandy Gallant. Extra
large version |
Second anchor mount. Extra large version |
Shroud shields, Bill and Sandy Gallant |
Detail of shroud shields, Bill and Sandy Gallant |
Stanchion, Bill and Sandy Gallant |
|
|
Pop-top enclosure folding, step 1
Roger Pihlaja |
Pop-top enclosure folding, step 2
Roger Pihlaja |
Pop-top enclosure folding, step 3
Roger Pihlaja |
Pop-top enclosure folding, step 4
Roger Pihlaja |
Pop-top enclosure folding, step 5
Roger Pihlaja |
Pop-top enclosure folding, step 6
Roger Pihlaja |
OEM outhaul, as of Sept., 98 |
Outhaul on Raven (Gray Sanford). |
Gary Sanford rigging Raven in the dark |
Trim ballast, John Le Clare's project boat |
Wider view of John Le Clare's project. |
|
Pop top slide, Blew Daze, Pamela Vana & Alex Bell |
Gooseneck and main furler, Blew Daze |
Side view of the gooseneck, Blew Daze |
Traveler car, Blew Daze |
End detail of traveler, Blew Daze |
|
New motor mount design retrofitted to Alex Bell's old boat. |
Furling lead block, Blew Daze |
|
Bimini Room on Roger P's Dynamic Equilibrium |
Bimini Room with awning, Dynamic Equilibrium |
Annotated bow of Dynamic Equilibrium |
Bimini room aft view |
Convertible bimini top side view |
Anderson 12ST stainless steel self tailing sheet winch & a Harken
Speedgrip winch handle on Dynamic Equilibrium |
Bill Sparhawk's (now Ron Finelli's) boom car |
Bill's spinnaker track and slides |
Bill's traveller setup |
Bill's boom vang solution |
Rhodes 22 hull in the mold |
Hoisting New Song |
Marc's mast hoist |
 |
|
|
|
|
Roger Pihlaja Trailer Jack System #1 |
Roger Pihlaja Trailer Jack System #2 |
Roger Pihlaja Trailer Jack System #3 |
|
|
|
Roger Pihlaja Kayak Carrier System #1 |
Roger Pihlaja Kayak System #1 |
Roger Pihlaja Kayak System #2 |
|
|
|
Roger Pihlaja Kayak System #3 |
Tom Deliberto's UPS Sail and associated emails |
|
|
Information
on Centerboard
and Trunk Restoration (Courtesy of Lou Rosenberg and Roger Pihlaja)
